Home The Truck Our Equipment Meet the Crew RPR Clients Contact Us Links & Awards
Return to RPR Equipment Main Page
Bryston 2B (1)

missing image: Bryston2B.jpg

Accuracy in Performance - Elegance in Appearance
Bryston Amplifiers


The Bryston 2B-LP amplifier is a compact, high quality 60 watt per channel, (8ohms), stereo amplifier intended for use in sound systems requiring a musically accurate, extremely reliable, no compromise power source.

While the 2B-LP has for years been thought of as an exceptionally lucid and transparent amplifier for traditional two-channel stereo setups, it is now finding additional acceptance in such installations as multimedia surround-sound systems, and in the most ambitious music systems with multi-amplified speakers using electronic crossovers.

Features include: Completely separate stereo channels, including dual power supplies, to prevent any interaction between left and right signals, for precise soundstaging and image quality. Green/red power/clipping lights to give immediate indication of any overload or fault condition. Rear-mounted ground-lift switching to avoid potential ground loops and system hum. Gold plated five-way binding posts and gold plated RCA connectors to prevent any possibility of long term corrosion or connector distortion. Finally, higher power monaural operation is as easy as the flick of a rear-mounted stereo/mono switch.

Bryston exclusively uses only the finest components in our designs, such as 1% metal-film resistors, polystyrene capacitors and hand-matched transistors to reduce noise and distortion to the absolute minimum. All signal circuitry is fully discrete to avoid the compromises, phase shift and nonlinearities inherent in IC's. Bryston applies techniques and employs custom materials in our everyday construction of electronic equipment which are more typically found in military and aerospace industries.

If your requirements are sonic excellence, ultimate reliability, system flexibility and superb value, Bryston power amplifiers will surpass your every performance criterion.


2B-LP Specification

Power Output: 60 watts per channel. 8 ohms
100 watts per channel 4 ohms
200 watts, bridged. 8 ohms
Gain: 28.28 or 29dB
Harmonic distortion: Less than 0.01% from 20Hz to 20kHz at 60 Watts
IM distortion: Less than 0.01% from 10 milliwatts to 60 watt
Noise: 100dB below full output
Crosstalk: Below noise 20Hz to 20 kHz at 60 Watts
Slew Rate: Greater than 60 volts per microsecond
Power bandwidth: 5Hz to over 100kHz
Damping factor: Over 500 at 20Hz. ref. 8 ohms
Input Sensitivity: 0.775 Volts in = 60 Watts at 8 Ohms
Input Impedance: 50 Kohms unbalanced


Features
  • Bridging switch
  • Ground lift switch
  • Over 1600 cm/square of heatsinking; over 3200 cm2 with chassis
  • Regulated power supply to all voltage gain stage
  • Each channel separated back to the linecord
  • Channel clipping indicator
  • Green = normal levels, Red = clipping
  • Will deliver full output to any phase angle at 4 ohms or higher
  • Gold-plated RCA jacks

A/C Power
    Consumption & Heat Load
  1. Idle Current 58W
  2. Stereo 8 Ohms (50W ea.) 286W
  3. Stereo 4 Ohms (100W ea.) 498W
  4. Bridged 8 Ohms (200W) 504W
  5. Max. Wattage 504W
  6. Max. Heat Dissipation 304W / 1037 Btu/Hr
Dimensions 19 x 1.75 x 10 inches, wt: 18 lbs
48.25 x 4.44 x 25.4cm, wt: 8kg
Click here to visit the Bryston website

HOME | THE TRUCK | EQUIPMENT | THE CREW | CLIENTS | CONTACT US | LINKS & AWARDS
1170 Greenwood Lake Turnpike Ringwood, NJ 07456 ph: 973-728-8114 fax: 973-728-8761